COURSE NAME:ASME B31.3 Process Piping


UPCOMING EVENTS


START DATE END DATE CITY/COUNTRY PRICE Request
 12-11-2017  16-11-2017  Riyadh/Saudi Arabia Register
INTRODUCTION:
  • Piping plays vital role in Process Plants. If not properly designed or fabricated piping suffers many leakages/ failures. These failures lead to major fires and ultimately loss to business.
OBJECTIVES:
  • This course is designed to increase knowledge in the area of piping in general and process piping in specific. This advanced, fast-paced program provides the participants with working knowledge of the design philosophy and engineering practices employed in the design, fabrication and erection/commissioning requirements of process piping's.
  • Many of the derivations of the formulas used in ASME Section 31.3 are discussed to satisfy design and construction requirements on practical grounds. Hands-on design problem solving is integrated throughout the program.
OUTLINE:

Day 1

Session 1

  • Introduction and Bench Mark Quiz
  • Piping codes and standards
  • Standards for Piping Components
  • Pipe flanges and fittings

Session 2

  • ASME B 31.3 Scope and applicability
  • Service/Fluid Classification and Definitions
  • Design Philosophy of B31.3
  • Joint Quality Factors / Increased Quality factors
  • Allowable stresses
  • Design for Internal Pressure
  • Case Study-1

Session 3

  • Case Study-2
  • Design of permanent blanks
  • Case Study-3
  • Practice Exam-1 (closed Book)

Day 2

Session 1

  • Points to recall Day-1
  • Selection of Fittings and Flanges
  • Pressure-temperature ratings.

Session 2

  • Design of Nozzles –reinforcements
  • Case Study 3
  •  Review of Exam-1

Session 3

  • Service considerations in Design
  • Support Systems for piping
  • Flexibility considerations
  • Materials Review
  • Common piping Materials
  • Listed, unlisted materials
  • Temperature Limitations
  • Home Work - 1

Day 3

Session 1

  • Points to recall Day-2
  • Review Of Home work - 1
  • Material Identification, Certification and Traceability

Session 2

  • Impact testing for Low temperature service
  • Acceptance Criteria for Impact Testing.
  • Case Study 4

Session 3

  • Weld Edge prep. And Fit-up tolerances
  • Welding Procedures and Qualification Testing
  • Welder Qualification
  • Weld size for attachment welds at openings.
  • Socket welds, Seal welds
  • Permitted Weld reinforcements
  • Practice Exam-2. ( Open Book)

Day 4

Session 1

  • Review of Practice Exam 2 (Open Book)
  • Preheat Temperature
  • Post Weld Heat Treatment
  • Hardness Testing after PWHT

Session 2

  • Non Destructive Examination Requirements
  • NDE Procedures and Requirements
  • NDE Personnel Qualifications
  • NDE Methods
  • Extent of NDE Examination
  • Acceptance Criteria
  • Quality Records

 Session 3

  • Leak testing-Hydrostatic
  • Leak testing-Pneumatic
  • Service leak test
  • NDT in lieu of leak test
  • Home Work - 2

Day 5

Session 1

  • Additional requirements for Category M fluids
  • Additional requirements for Category K fluids

Session 2

  • Additional requirements For Non metallic Piping
  • Final close book test

Session 3

  • Final open book test
  • Feed back, concluding and close down

 

WHO SHOULD ATTEND:
  • This course is suitable for engineers/supervisor, managers who desires to have thorough knowledge as well as practical requirements of ASME B31.3 Process Piping and those who come across day to day in practical, the usage of the above code.

 

DURATION:
    • 5 Day(s)
  •  


    The presentation is generally appealing to me. The dedication & devotion of the instructor are both laudable & admirable.
    Mohammed F. Alotaibi
    Sabic

    Really this course is important for any inspector, so I will recommended it for our employees. And thanks a lot!
    Ahmed Al-Yami
    Sabic

    You are doing excellent bringing such very talented instructor. Please keep it up.
    Ahmed Afifi
    Al-Zamil CoolCare

    I would like to appreciate you as well as the instructor for a good training due to the fact that the helping to gain new information about the types of valve with advantages and disadvantage as well. Many thinking.
    Zaki Ali Aldawood
    Sabic

    This course was very beneficial and helpful to understand one of the Major NDT method. I encourage ITC to continue with this performance.
    Talal Saad AlHasawi
    Sabic

    ITC service was in overall excellent. Thanks.
    Wael M. Morsy
    Mobily

    This course was good and a nice guide to the PMP exam. Thanks.
    Yazeed Mohamed Mreki
    General Authority of Civil Aviation (GACA)

    It was good course & good preparation with excellent instructor. Thanks a lot.
    Faisal Mahdi Al-Qahtani
    Sabic

    It was a nice course to have. I suggest taking this course with the same instructor to other people. Thanks for the instructor for his kindness & helfull during the course.
    Abdul-Moniem Al-Humoud
    Sabic

    It is very important course, which enable us to improve our knowledge to work approaching our big account and can be recall us the key account. This is will support us to active result for the best of the Co.
    Mohammed Amjad
    Al-Suwadi Services

    The instructor is highly and technical knowledgeable in explaining all the subject in the course taken.
    Noel V. Garan
    Coldstorec Group Of Saudi Arabia

    Instructor was well prepared and knowledgeable I gain lot of useful information.
    Gulam Khan
    Saudi Aramco

    It was a good learning experience. Got to know the concept involved in key account.
    Muthuraman Nachiappan
    Al-Suwadi Services

    The instructor Mr. Ahmed Sabry has a very nice spirit.
    Salam Fakhoury
    Al Khodari Company

    It is very useful to us and increase our knowledge.
    Mohammed Rashed Afifi
    Al Khodari Company

    The course is excellent and helpful. It help me in organizing the work in more safe manner.
    Muzammil Hayat
    Al Khodari Company

    The instructor is very knowledge and hard working, his way of teaching is very good.
    Ibrahim Darwish
    Al Khodari Company