COURSE NAME:Electrical Workshop Testbench


This course can be scheduled at your convenience, to request this course please click here

To successfully inspect and test electrical equipment, Electrical personnel must first fully understand the technology of the equipment. After the successful start-up and subsequent continued operation, electrical equipment requires periodic inspection and testing.

This will ensure the electrical equipment operates correctly so that production is maximized in a safe, cost effective and efficient manner.


On successful completion of this workshop, participants will have:


  • Better understanding of inspection and testing methods
  • Better understanding of troubleshooting procedures
  • Improved capability in the use of test equipment
  • Refreshed outlook on reading electrical drawings
  • Refreshed awareness of electrical safety concerns


Day 1


The Technology of Electrical Workshop Equipment

  • Transformers
  • Power supplies (UPS)
  • Batteries
  • Generators
  • Switchgear
  • Motor control centers (MCC)
  • Disconnect switches
  • Neutral ground resistors (NGR)
  • Variable frequency/speed drives (VFD/VSD)
  • Programmable logic controllers (PLC)
  • Power monitoring
  • Control relays/timers/switches
  • Motor/feeder protective devices
  • Motors (AC & DC)
  • Miscellaneous equipment - heaters, solenoid valves and electric valve actuators

Day 2

The Use of Test bench Equipment

  • Digital voltmeter (DVM)
  • Oscilloscopes
  • Megger
  • Frequency meter
  • Temperature probes/pyrometers
  • Ammeters
  • Power meters
  • Load banks
  • Digital hydrometers
  • Cable fault locators

Day 3

Inspection and Testing of Electrical Workshop

  • Methods
  • Terminology
  • Principles
  • Special techniques
  • Troubleshooting of Electrical Equipment
  • Methods
  • Terminology
  • Principles
  • Special techniques
  • Case studies/examples
  • Single line drawings
  • Group exercises

Day 4

The Necessity for Electrical workshop Test bench

  • Common mode failures
  • Phase imbalance
  • Contact pitting/arcing
  • Electronic component failure
  • Fusing
  • Motor windings/bearings/brushes
  • Ballasts
  • Excitation circuits
  • Battery cells
  • Inverters/rectifiers
  • Bushings
  • Switches
  • Control circuits
  • Ground faults
  • Open session: Case Studies, Questions and Answers


Day 5

The Interpretation and Use of Drawings and Safety

  • Single-line electrical drawings
  • Control schematics
  • Wiring lists
  • P&ID’s
  • Logic and standard symbols.
  • The Development of a Job Plan
  • Identification of the troubleshooting step-by-step sequence
  • Procedure preparation
  • Documentation
  • Safety considerations and training
  • A review of Safety Requirements
  • Area classifications
  • NEC electrical codes




This workshop is intended for Electrical Engineers, Electrical Supervisors and Electrical Technicians engaged in the inspection and testing of Electrical Equipment.

    • 5 Day(s)

    The presentation is generally appealing to me. The dedication & devotion of the instructor are both laudable & admirable.
    Mohammed F. Alotaibi

    Really this course is important for any inspector, so I will recommended it for our employees. And thanks a lot!
    Ahmed Al-Yami

    You are doing excellent bringing such very talented instructor. Please keep it up.
    Ahmed Afifi
    Al-Zamil CoolCare

    I would like to appreciate you as well as the instructor for a good training due to the fact that the helping to gain new information about the types of valve with advantages and disadvantage as well. Many thinking.
    Zaki Ali Aldawood

    This course was very beneficial and helpful to understand one of the Major NDT method. I encourage ITC to continue with this performance.
    Talal Saad AlHasawi

    ITC service was in overall excellent. Thanks.
    Wael M. Morsy

    This course was good and a nice guide to the PMP exam. Thanks.
    Yazeed Mohamed Mreki
    General Authority of Civil Aviation (GACA)

    It was good course & good preparation with excellent instructor. Thanks a lot.
    Faisal Mahdi Al-Qahtani

    It was a nice course to have. I suggest taking this course with the same instructor to other people. Thanks for the instructor for his kindness & helfull during the course.
    Abdul-Moniem Al-Humoud

    It is very important course, which enable us to improve our knowledge to work approaching our big account and can be recall us the key account. This is will support us to active result for the best of the Co.
    Mohammed Amjad
    Al-Suwadi Services

    The instructor is highly and technical knowledgeable in explaining all the subject in the course taken.
    Noel V. Garan
    Coldstorec Group Of Saudi Arabia

    Instructor was well prepared and knowledgeable I gain lot of useful information.
    Gulam Khan
    Saudi Aramco

    It was a good learning experience. Got to know the concept involved in key account.
    Muthuraman Nachiappan
    Al-Suwadi Services

    The instructor Mr. Ahmed Sabry has a very nice spirit.
    Salam Fakhoury
    Al Khodari Company

    It is very useful to us and increase our knowledge.
    Mohammed Rashed Afifi
    Al Khodari Company

    The course is excellent and helpful. It help me in organizing the work in more safe manner.
    Muzammil Hayat
    Al Khodari Company

    The instructor is very knowledge and hard working, his way of teaching is very good.
    Ibrahim Darwish
    Al Khodari Company